FREE delivery for orders above £450.

All-Weather Wall & Floor Tile Adhesive 20kg Grey Pallet of 54

Code: TF4893

ALL-WEATHER is a grey cement-based, thin-bed ceramic tile adhesive, which conforms to BS EN 12004 Type C, Class 1T and is recommended when fixing ceramic floor and wall tiles, mosaics, natural and lightweight pre-cast cladding brick slips to solid masonry substrates. ALL-WEATHER is fully water-resistant; frost-resistant; suitable for interior / exterior use and in swimming pools and locations which are subject to excessive dampness, e.g. showers, saunas and bathrooms.

£349.99 £419.99 Inc VAT

The delivery charge is £42 for orders below £450. Orders above £450 qualify for free delivery. Delivery lead time is 5 working days from the date of the order. We advise that customers wait for their goods to be delivered before arranging work to be undertaken. Building Materials Wholesale may not be held liable for any failure to deliver by any stated time or date or any consequential loss resulting from late delivery. See Full Transport Policy

In Stock

Description

Description

PALACE ALL WEATHER is a grey cement-based, thin-bed ceramic tile adhesive, which conforms to BS EN 12004 Type C, Class 1T and is suitable for fixing semi-porous ceramic and natural stone FLOOR and WALL tiles in interior & exterior locations. PALACE ALL-WEATHER offers an economical means of fixing semi-porous tiles onto solid, stable masonry surfaces and securely fixed & suitably rated Tile Backer boards. PALACE ALL-WEATHER gives excellent compatibility & bond strength with concrete, cement render & cement screed surfaces, whilst providing excellent water resistance. PALACE ALL-WEATHER WHITE is particularly recommended when fixing light coloured semi-porous natural stone such as Marble and Travertine.

  • Fully water-resistant for Interior & Exterior use
  • Excellent non-slip with extended pot-life > 4 hours
  • Fixes ceramic, mosaic & natural stone tiles to semi-porous surfaces
  • For fixing to heated sub-floors & areas subject to heavy traffic
  • For use in pools, showers & wet areas including under full immersion

Surface Preparation:

The substrate must be clean, firm and free of dust, dirt, oil, grease and lose flaking coatings. They must also be structurally sound and strong enough to support the weight of the tiles being fixed. PALACE ALL-WEATHER can be applied to dry or damp surfaces however moisture-sensitive materials must be dry and remain dry after fixing. Worn or porous masonry surfaces should be sealed with PALACE TILERS PRIMER diluted as 1 to 3 with water. PALACE ALL-WEATHER can be applied to cement-based Tile Backer boards over-laid onto a fully rigid structure, such as well-braced 15mm waterproof ply-board screw fixed at 300mm centres to supporting battens. Do not apply onto bare, un-sealed gypsum plaster or anhydrite floor screed before first priming this type surface with two coats of neat PALACE TILERS PRIMER the first diluted 1 to 1 and the second neat.

Mix Preparation:

PALACE ALL-WEATHER should be added to water in a clean container whilst mechanically stirring and mixed thoroughly to give a soft, slump-free, easily worked mortar. The recommended mixing proportions by volume are 1-part water to 3 parts powder [5 litres per 20kg sack of powder or the equivalent weight ratio]. The consistency of the paste can be adjusted with slight additions of water or powder at the initial mixing stage, however, the part-used adhesive should never be “freshened up” with later water. PALACE ALL-WEATHER will remain useable for about 4 hours and should not be applied in temperatures below 5’C. In ideal conditions (20’C), this thin bed adhesive will set after about 12 to 16 hours.

Application Method:

For fixing ceramic tiles or mosaics, use a notched trowel to give a ribbed mortar bed on the substrate, into which the tiles are firmly bedded with a twist and slide action to ensure full contact. Use a 3mm x 3mm notch at 6mm centres for mosaics and thin flat-backed wall tiling, a 5mm x 5mm notch at 10mm centres for general wall tiling and 10mm x 10mm notch at 16mm centres for floor tiling. The position of the tiles can be adjusted up to 10 minutes after initial fixing. The open time of the exposed mortar bed is approximately 30 minutes, depending on surface porosity and site temperatures. It is recommended that tiles with raised or studded back profiles, (or in situations where dampness is likely after tiling), should be back-buttered to ensure solid bed fixing. Do not trowel out an area of adhesive greater than can be tiled over within a 10-minute period. Surfaces, such as tamp-rutted concrete and masonry block-work, that are rough or uneven should be prepared with PALACE SELF-LEVEL floor smoothing & levelling compound and when sufficiently firm (24 – 48 hours later), followed by an application of PALACE ALL-WEATHER adhesive. Do not apply any cement-based adhesive onto bare, unsealed gypsum plaster or anhydrite screeds and do not allow adhesive residues to set & harden on the tile face. Do not mix or apply this adhesive when air or ground temperatures are forecast to be below 5’C or greater than 35’C at any time during the first 24 hours after application.

Coverage:

When fixing on a level, even surface using a 10mm notched trowel, PALACE ALL-WEATHER will cover at a rate of about 4kg per sq. meter for heavy-duty, studded tiles. When applying wall tiles, the product will cover at about 2.5 kg per sq. mtr.

Grouting:

Grouting may proceed as soon as the tile bed is sufficiently firm, which for PALACE ALL-WEATHER will be after at least 24 hours at room temperature. This period however will be extended in cold conditions. When the adhesive is fully set, wall & floor joints can be grouted using PALACE COLOUR-LOCK GROUT or PALACE ANTI-MOULD GROUT, however, on wider flooring applications, joints of up to 20mm wide can be grouted using PALACE WIDE JOINT FLEXI FLOOR TILE GROUT.

Storage & Packaging:

PALACE ALL-WEATHER is supplied in 20kg multi-ply, moisture-resistant paper sacks and has a storage life of not less than 12 months if stored in dry, un-opened conditions.

Specifications

Additional information

Weight 1080 kg
Application

Floor, Wall

Brand

Palace Chemicals

Colour

Grey

Product Form

Powder

Product Type

Ceramic Tile Adhesive

Size

20 kg

Unit of Measure

Kilogram(s)

Performance

Frost Resistant, Water Resistant

Receiving Surfaces

Cement faced fibre boards, Concrete, Concrete brick/block, Firm and stable plaster, Plasterboard, Sand/Cement Render, Sand/Cement Screed, Tile Backer

Setting time

24 hours at 20°C

Usage

Bathrooms, Saunas, Swimming Pools

Product Documents

Technical Datasheet

Download

Material Datasheet

Download

Declaration of Performance

Download

Questions & Answers

Questions and answers of the customers

There are no questions yet. Be the first to ask a question about this product.

Send me a notification for each new answer.

Customer Product Reviews

Reviews

There are no reviews yet.

Be the first to review “All-Weather Wall & Floor Tile Adhesive 20kg Grey Pallet of 54”
Review Title

Your email address will not be published.

1 × 1 =